PRTG Manual: SNMP Linux Physical Disk Sensor

The SNMP Linux Physical Disk sensor monitors the input/output (I/O) on disks of a Linux/Unix system via the Simple Network Management Protocol (SNMP).

SNMP Linux Physical Disk Sensor

SNMP Linux Physical Disk Sensor

i_square_cyanFor a detailed list and descriptions of the channels that this sensor can show, see section Channel List.

Sensor in Other Languages

  • Dutch: SNMP Linux Fysieke Schijf
  • French: Linux disque physique (SNMP)
  • German: SNMP Linux Physikalischer Datenträger
  • Japanese: SNMP Linux 物理ディスクを監視する
  • Portuguese: Disco físico Linux (SNMP)
  • Russian: Физический диск Linux по SNMP
  • Simplified Chinese: SNMP Linux 物理磁盘
  • Spanish: Disco físico Linux (SNMP)

Remarks

Consider the following remarks and requirements for this sensor:

Remark

Description

IPv6

This sensor supports IPv6.

Performance impact

This sensor has a low performance impact.

Knowledge Base

Knowledge Base: Monitoring Linux problem - SNMP port not reachable

Basic Sensor Settings

Basic Sensor Settings

Basic Sensor Settings

The sensor has the following default tags that are automatically predefined in the sensor's settings when you add the sensor:

  • physicaldisk
  • snmpphysicaldisksensor

i_square_cyanFor more information about basic sensor settings, see section Sensor Settings.

Physical Disk Settings

Physical Disk Settings

Physical Disk Settings

Setting

Description

Disk

The physical disk that this sensor monitors.

BitMask

The bitmask that might be necessary for bug tracking purposes.

Sensor Display

Sensor Display

Sensor Display

Setting

Description

Primary Channel

Select a channel from the list to define it as the primary channel. In the device tree, PRTG displays the last value of the primary channel below the sensor's name. The available options depend on what channels are available for this sensor.

i_round_blueYou can set a different primary channel later by clicking b_channel_primary below a channel gauge on the sensor's Overview tab.

Graph Type

Define how this sensor shows different channels:

  • Show channels independently (default): Show a graph for each channel.
  • Stack channels on top of each other: Stack channels on top of each other to create a multi-channel graph. This generates a graph that visualizes the different components of your total traffic.
    i_round_redYou cannot use this option in combination with manual Vertical Axis Scaling (available in the channel settings).

Stack Unit

This setting is only visible if you select Stack channels on top of each other above.

Select a unit from the list. PRTG stacks all channels with this unit on top of each other. By default, you cannot exclude single channels from stacking if they use the selected unit. However, there is an advanced procedure to do so.

Inherited Settings

By default, all of these settings are inherited from objects that are higher in the hierarchy. We recommend that you change them centrally in the root group settings if necessary. To change a setting for this object only, click b_inherited_enabled under the corresponding setting name to disable the inheritance and to display its options.

i_square_cyanFor more information, see section Inheritance of Settings.

Channel List

i_round_blueWhich channels the sensor actually shows might depend on the target device, the available components, and the sensor setup.

Channel

Description

Bytes Read

The number of bytes read

i_round_blueThis channel is the primary channel by default.

Bytes Written

The number of bytes written

Downtime

In the channel table on the Overview tab, this channel never shows any values. PRTG uses this channel in graphs and reports to show the amount of time in which the sensor was in the Down status

Load Average (1 Minute)

The load average (1 minute) (%)

Load Average (5 Minutes)

The load average (5 minutes) (%)

Load Average (15 Minutes)

The load average (15 minutes) (%)

Read Accesses

The number of read accesses

Write Accesses

The number of write accesses

More

i_square_blueKNOWLEDGE BASE

Monitoring Linux problem - SNMP port not reachable

What security features does PRTG include?

My SNMP sensors don’t work. What can I do?